Ceramic coating and thermal insulation service for exhaust systems

The thermal spray process
  • We have the technology, the know-how and innovative products.
  • A thermal insulation supplier for motorsport and tuning across the Baltics.
  • We have a solution for heat management.

Using thermal spraying, a metallizing process, we apply ceramic coatings to exhaust systems, engine parts and brake systems.

Relative surface temperature of a part
Uncoated
100%
Coated, 0.3 mm
67–75%

About 25–33% lower surface temperature at 0.3 mm coating thickness. The result depends on the part, its material and the engine.

Heat shields

Coated heat shields

For places where an exhaust pipe sits too close to something and there is too much heat.

  • Works with coated exhaust parts as one solution
  • Holds back radiated heat where a coating alone does not help
  • Protects paint and lines next to the exhaust system
  • Lower temperature in the cabin

See heat shields

  • 4-1 exhaust manifold with a matte ceramic coating and embossed stainless steel heat shields on all four runners
  • Ceramic-coated downpipe with a heat shield wrapped around its middle section
  • Round heat shields in several sizes and one flat shield, made from embossed stainless steel foil

Benefits

What a TBC thermal barrier coating does for your exhaust system and engine.

  1. Protects metal parts from overheating and weld seams from cracking

  2. On naturally aspirated engines, a steady exhaust gas speed, because the heat stays in the gas instead of the metal

  3. Lower coolant and engine oil temperatures, as the coated exhaust helps carry heat away from the engine

  4. Better power curves, an engine that revs higher, and quicker, easier tuning on the dyno

  5. Better acceleration, and an exhaust that reaches working temperature sooner

  6. All benefits

Our work

Heat shields, coated parts and our latest work on Instagram and Facebook.

  • Curved turbo downpipe with a ceramic coating and a heat shield on the straight section
  • Ceramic-coated exhaust pipe with a heat shield held in place by a clamp
  • Three round heat shields of different diameters, made from embossed stainless steel foil
  • Two long round heat shields for pipes

Modern lubrication solutions

SWEPCO oils and lubricants

Modern lubrication solutions for motorsport and industry from a maker of premium specialty lubricants.

  • Using SWEPCO oils in motorsport since 2000
  • SWEPCO oils have been used by our Latvian champions and legends
  • SWEPCO oils and lubricants last longer than ordinary conventional oils, up to 2–3 times longer

About SWEPCO oils

Authorised SWEPCO distributor since2000

  • Engine oils
  • Transmission oils
  • Lubricants

How TBC thermal barrier coating works

In motorsport, tuning and aviation, TBC stands for thermal barrier coating: a high-tech ceramic coating for parts exposed to extreme heat, such as exhaust manifolds, turbine housings, piston crowns and the whole exhaust system.

A special ceramic composition, often based on zirconium oxide, acts as a strong heat insulator and stops the metal surface from soaking up heat. The heat stays in the exhaust gas instead of being absorbed by the metal of the exhaust system. In a race car the engine and exhaust run at 800 °C to more than 1000 °C, which is why this thermal management matters so much.

TBC thermal barrier coating for engine and exhaust parts

Drawing of a coated four-into-one exhaust manifold with a magnified section through the coating layers0.3 mm1234
  1. Ceramic layer, about 0.3 mm
  2. Metal bond layer
  3. Steel wall of the part
  4. Hot exhaust gas

Parts we coat

Every part is quoted individually. Pick yours to see what coating does for it and how to send it in.

  • Exhaust manifold

    Cast manifolds and tubular headers: the hottest part of the exhaust and the best place to start.

  • Turbo housing

    The turbine housing is a heat source right next to your intake. Coating it cuts heat soak.

  • Downpipe

    The pipe right after the turbo, often routed past the gearbox, driveshaft and floor.

  • Intake manifold

    Keeps engine heat out of the intake air on its way to the cylinders.

  • Pistons

    A ceramic layer on the crown limits how much combustion heat soaks into the piston.

  • Brake pads and shims

    A heat barrier between the pad and the caliper that keeps brake fluid cooler.

  • Motorcycle exhaust

    Headers and collectors that run close to your legs, the frame and the fairings.

Sending a part by courier

Most parts reach us by courier. It takes three steps.

  1. Send photos and details

    Use the form or WhatsApp. Tell us the part, the car or engine, and anything we should know, such as cracks or earlier repairs.

  2. Pack and ship the part

    Once you accept the quote, remove sensors, gaskets and heat shields, pack the part well and ship it with any courier.

  3. Get it back coated

    We coat the part and send it back to you, or you pick it up in Riga.

Shipping address

We send the shipping address together with your quote.

Packing tips

  • Wrap flanges and threads so they cannot be damaged in transit.
  • Use a sturdy box and fill the empty space so the part cannot move.
  • Put a note inside with your name, phone number and what you want coated.

Who we coat for

Drift, rally and circuit cars, tuned road cars, motorcycles, and small batches for workshops and fabricators.

  • Motorsport

    Drift, rally and circuit cars that run hot for a whole session.

  • Tuning

    Road cars with more power than the factory planned for, and more heat to match.

  • Motorcycles

    Less heat on the rider, the frame and the electrics.

  • Industrial and B2B

    Exhaust fabricators, workshops and small batches of industrial parts.

Common questions

What is a thermal barrier coating?

A ceramic layer that slows down heat moving through a part. Ours is metal-ceramic: a metal bond layer and ceramic oxide layers applied by thermal spray.

How much does ceramic exhaust coating lower the temperature?

About 25–33% lower surface temperature at 0.3 mm coating thickness is typical. The exact result depends on the part, the material and how the engine is used.

Is this the same as ceramic coating for car paint?

No. Paint-protection ceramic coatings are thin, glass-like layers for bodywork. We coat hot engine and exhaust parts with a heat barrier.

Which parts can you coat?

Exhaust manifolds and headers, turbo housings, downpipes, intake manifolds, piston crowns, brake pad backing plates and shims, motorcycle exhausts and other hot engine parts. Send a photo if you are not sure.

All questions and answers

Get a quote for your part

Tell us what you want coated and add a few photos. We reply with a price and a timeline.

For example: BMW E46 M3 with S54 engine, or Honda CBR600RR 2008

Race or road use, known problems, your deadline

Photos (optional)

Up to 6 photos. Large photos are made smaller before sending.

WhatsAppCallGet a quote